FGD Silicon carbide spray nozzles

FGD Silicon carbide spray nozzles manufactured by our factory are durable, corrosion-resistant, and efficient. Buy from us for high-quality products at affordable prices.

Request a Quote
  • FGD Silicon carbide spray nozzles
  • FGD Silicon carbide spray nozzles

PRODUCTS DETAILS

Tangential Swirl Nozzle             WET FLUE GAS DESULFURIZATION WITH LIME/LIMESTONE SLURRY  Our products have a long service life, which is the same as the famous international brands: SPRAY, BETE, LECHLER. Features Desulphurisation efficiency above 99% can be achieved Availability of over 98% can be achieved Engineering not dependent on any specific location Marketable product Unlimited part load operation Method with largest number of references in the world
Property Value
Density (kg.m-3) 3030
Apparent Porosity (%) 0
Young’s Modulus (GPa) 400
Bend Strength (MPa) 390
Hardness (VHN) 2500
Thermal Expansion Coefficient (x 10-6/ºC) 4.3
Thermal Conductivity (W/m.K) 145
Maximum Use Temperature (ºC) 1375
  Purification of flue gas by lime suspension
For the wet desulphurisation of flue gas, it is passed through an absorber (scrubber). The lime suspension offered in the absorber (limestone or lime milk) reacts with the sulphur dioxide from the flue gas. The better the mass transfer, the more effective the desulphurisation is. Simultaneously with the absorption, the flue gas is saturated with water vapour. The so-called "clean gas" is usually discharged via a wet chimney or cooling tower. The water thus lost for the process must be replaced. The lime slurry pumped in circulation is kept chemically active by repeatedly draining a saturated partial flow and replacing it with new reactive suspension. The drained part flow contains gypsum, which – simplified – is a reaction product of lime and sulphur and can be marketed after dewatering (e.g. for gypsum walls in the construction industry). Special ceramic nozzles are used to inject the lime suspension into the absorber. These nozzles form many small droplets from the pumped suspension and thus a correspondingly large reaction surface for good mass transfer. The ceramic material permits long service life despite the fact that lime suspension with gypsum content has abrasive properties. In the design we attach great importance to free cross-sections, so that smaller impurities in the suspension cannot set the nozzles. For economical operation, these nozzles can be adapted to the highest efficiency range of the pump. A nozzle can be specified for (almost) every process engineering challenge. In addition to full-cone and hollow-cone nozzles in various spray angles and flow rates, the ZPC nozzle with patented twist compensation is also available. The absorption zone consists of several levels of nozzles and a horizontally installed droplet separator system, in order to return the fine droplets carried along in the gas stream to the process. With our high performance droplet separators you can increase the efficiency of your plant. The solids in the suspension can lead to deposits, e.g. in the droplet separator, in the inlet duct or on pipes, which can lead to problems in operation. Since water is always withdrawn from the circuit through evaporation, water must be fed into the absorber, which can and should be used for cleaning. ZPC tongue nozzles have proven themselves for cleaning the flue gas inlet. ZPC full cone nozzles are usually used for cleaning the droplet separators. Plastics (e.g. for pipelines) and rubber (e.g. gaskets, rubber linings, etc.) are often used in an absorber whose temperature resistance is lower than the temperature of the uncooled flue gas. Normally, the suspension pumped in a circuit cools the flue gas sufficiently, but if, for example, the feed pump is suspended, the plastics and rubbers could be destroyed. Small special-alloy metal nozzles have proven their worth here, which take over cooling during this time and thus protect the investment of the flue gas desulphurisation plant.
1 喷嘴和检测 Reaction bonded silicon carbide (SiSiC): Moh's hardness is 9.2, with excellent resistance to erosion and corrosion, excellent abrasion-resistance and anti-oxidation. It is 4 to 5 times stronger than nitride bonded silicon carbide. The service life is 7 to 10 times longer than alumina material. The MOR of RBSiC is 5 to 7 times that of SNBSC, it can be used for more complex shapes.

Hot Products

Special Ceramic lined pipe-- wear resistant, corrosion resistant and high temperature resistant silicon carbide ceramic lined tube

Special Ceramic lined pipe-- wear resistant, corrosion resistant and high temperature resistant silicon carbide ceramic lined tube

wear resistant ceramic lined apex

wear resistant ceramic lined apex

one way and double direction rbsic FGD nozzle

one way and double direction rbsic FGD nozzle

Fine technical SiC ceramic impeller

Fine technical SiC ceramic impeller

hydrocyclone RBSC Apex factory - hydrocyclone silicon carbide apex

hydrocyclone RBSC Apex factory - hydrocyclone silicon carbide apex

Full cone Spray nozzle 0.25inch

Full cone Spray nozzle 0.25inch

Wear Resistant SiCPU Silicon Carbide Poly Spigot and Cone liner

Wear Resistant SiCPU Silicon Carbide Poly Spigot and Cone liner

Flange vortex hollow cone nozzle

Flange vortex hollow cone nozzle

Технические данные и характеристики гидроциклона ГЦК

Технические данные и характеристики гидроциклона ГЦК

silicon carbide bushing

silicon carbide bushing

Contact us

Please feel free to give your inquiry in the form below We will reply you in 24 hours